Spyderco Standard Wire Clip Replacement

Spyderco Standard Wire Clip Replacement Deep Carry Titanium Clip

See our Finish FAQ page to learn more about our finishes.

This clip was designed specifically for Spyderco models that use their wire clip.

Whether or not the clip will work with a specific model depends on where the clip screw is in relation to the ‘channel tines’ (where the clip is held in the scales). If the screw is high in relation to those channels, there isn’t room to get a wrench on to tighten the clip down. If the screw is in the middle or lower area, the clip will work. Please see the compatibility tab for a list of compatible and incompatible models. If your model isn’t listed, please shoot an email and we’ll take a look at your model and get back to you.

These pocket clips are made here in Washington state from domestic 6AL-4V titanium, and are hand-formed and finished.  Each clip carries a lifetime guarantee - if you bend or tweak it, we'll replace it, no charge.

Specifications

Clip Material: Grade 5 6AL-4V Titanium

Clip Length: 2.0"

Clip Screw Hole Measurement (between center of each screw hole): N/A

Clip Screw Hole Diameter: N/A

Note: This clip DOES NOT come with a hardware packet that includes spare screws  due to how many different screw sizes wire clip models use. Most Spyderco OEM screws take a T6 or T8 (Torx) tool to remove.

Compatibility

Spyderco

WILL FIT

• Autonomy 1
• Caly 3
• Caly 3.5
• Chicago
• Dragonfly 2
• Foundry
  
• Lil Native Compression Lock (will not fit Lockback version)
• Manix 2 Lightweight
  
• MicroJimbo
  
• Para 3 Lightweight
• Poliwog
• Roadie XL
  
• Sage 2
• Sage 5 Lightweight
• Sage 5 Maxamet
  
• Siren
• Slysz Bowie (newer versions - will not fit the Gen 1 version)
• Slysz Bowie (KnifeJoy Exclusive)
  
• SpydieChef (newest ‘black screw’ version - will not fit older ‘silver screw’ models)
• Squeak
• Techno 1
• Techno 2 (fits newer version with centered clip screw)
• UKPK
• Urban
• Urban Lightweight

WILL FIT the following models that use a connected screw/barrel setup to hold the clip on the knife. On these models, if the screw and barrel both have drives, you need only to loosen the screw, then tighten it down from the opposite side once the clip is installed. If the screw has a drive, but the barrel side is plain (no drive), the screw and barrel need to be removed (before installation of the new clip), then re-installed with the screw head on the opposite side of the knife. The design of these knives puts the screw too high in relation to the ‘tine channels’ to get a driver through the access hole on the clip and onto the screw when the clip is place. But by flipping the barrel/screw around, it works well, as the clip can be tightened from the opposite side.

• Chaparral CF
• Chaparral FRN
• Ikuchi
• PITS
  
• UKPK FRN

BladeHQ

• Vox Dapper

Divo Knives

• Stout

Fox Knives

• Black Bird
• Chillin
  
• Core
• Baby Core
• Italico
• MKM
• Pelican Liner Lock
• Yaru
  

Giant Mouse Knives

• Ace Riv Titanium
• Ace Riv Brass
• Ace Riv Micarta
• Ace Clyde Brass
• Ave Clyde Micarta
• Ace Sonoma Micarta

Kabar

• Dozier

Kunwu

• S Tao
• X Tao CF (Carbon Fiber)

Luft Concepts

• AVNT
• Micro Burst

MKM

• Isonzo

North Arms

• Skaha II
  

Renegade Provisions Co.

• Gungnir (Wire Clip Model)

Vosteed

• Thunderbird

*Not all compatible models may be listed. Please email us if you have compatibility questions.